Quality RTOS & Embedded Software

 Real time embedded FreeRTOS RSS feed 
Real time embedded FreeRTOS mailing list 
Quick Start Supported MCUs PDF Books Trace Tools Ecosystem TCP & FAT Training




Loading

FreeRTOS demo for Freescale MK60DN512

Posted by bhight on February 5, 2015

Has anyone else run the FreeRTOS full demo (web server) with the IAR tool for the TWR-K60FD100M tower?

I am able to build and download, and it seems to work, but I am dropping a lot of Ethernet packets. I get 50% or more loss on pings. I have tried a regular cable and a null cable between a PC and the tower. I going to try to dig up a switch today and try through that.

Also, in the demo instructions on the freeRTOS site it says that the jumper on J6 on the main board needs to be set to pins 2-3. I think that they mean J10 (J6 is a header, not a jumper header) to set the system clock to CLKIN0 from the TWR-SER boarrd. I would like to confirm this.

Thanks.


FreeRTOS demo for Freescale MK60DN512

Posted by rtel on February 5, 2015

That is a very old demo, and all existing TCP work is done with our own TCP/IP stack. However I do seem to have a vague recollection of getting a similar issue - and the instruction on setting the jumper was the fix. It sounds like the board revision we used and the revision you have are different though, if the jumper in the documentation does not make sense on your board.

In any case the issue was, if I recall correctly, to do with the routeing of the clock to the PHY. With the jumper set incorrectly the PHY clock was out of sync with the CPU clock, but somehow it still seemed to work for about 50% of the packets. Using the jumper to sync the two clocks made the connection reliable.

Regards.


FreeRTOS demo for Freescale MK60DN512

Posted by bhight on February 5, 2015

Thanks for the reply. I had searched the forum but didn't find the original post.

I have tried all of the jumper settings for the clock with the same result. From the schematic it appears that I may need to route the clock from the TWR-SER board to the ENET_CLKIN input as well.

I'll try to find an older schematic to compare. Also, the demo targets a MK60DN512Zxxx10 device (Z = initial silicon), whereas our board has a MK60DN512xxx10. I have built for both with the same results.

I'll post back here if I make any progress. Thanks again.


[ Back to the top ]    [ About FreeRTOS ]    [ Sitemap ]    [ ]




Copyright (C) 2004-2010 Richard Barry. Copyright (C) 2010-2016 Real Time Engineers Ltd.
Any and all data, files, source code, html content and documentation included in the FreeRTOSTM distribution or available on this site are the exclusive property of Real Time Engineers Ltd.. See the files license.txt (included in the distribution) and this copyright notice for more information. FreeRTOSTM and FreeRTOS.orgTM are trade marks of Real Time Engineers Ltd.

Latest News:

FreeRTOS V9.0.0 is now available for download.


Free TCP/IP and file system demos for the RTOS


Sponsored Links

⇓ Now With No Code Size Limit! ⇓
⇑ Free Download Without Registering ⇑


FreeRTOS Partners

ARM Connected RTOS partner for all ARM microcontroller cores

Renesas Electronics Gold Alliance RTOS Partner.jpg

Microchip Premier RTOS Partner

RTOS partner of NXP for all NXP ARM microcontrollers

Atmel RTOS partner supporting ARM Cortex-M3 and AVR32 microcontrollers

STMicro RTOS partner supporting ARM7, ARM Cortex-M3, ARM Cortex-M4 and ARM Cortex-M0

Xilinx Microblaze and Zynq partner

Silicon Labs low power RTOS partner

Altera RTOS partner for Nios II and Cortex-A9 SoC

Freescale Alliance RTOS Member supporting ARM and ColdFire microcontrollers

Infineon ARM Cortex-M microcontrollers

Texas Instruments MCU Developer Network RTOS partner for ARM and MSP430 microcontrollers

Cypress RTOS partner supporting ARM Cortex-M3

Fujitsu RTOS partner supporting ARM Cortex-M3 and FM3

Microsemi (previously Actel) RTOS partner supporting ARM Cortex-M3

Atollic Partner

IAR Partner

Keil ARM Partner

Embedded Artists